How to Hang a Dartboard Cabinet

This article was co-authored by Norman Raverty and by wikiHow staff writer, Amy Bobinger. Norman Raverty is the owner of San Mateo Handyman, a handyman service in the San Francisco Bay Area. With over 27 years of experience, Norman has expertise in all five of the general building trades (carpentry, ceramic tile, drywall, electrical, plumbing).

This article has been viewed 103,044 times.

Whether you play darts as a casual pastime or you’re a pro at hitting the bullseye, sooner or later one of your darts is going to miss. To avoid damaging your wall or bending your dart tips, it’s a good idea to hang your dartboard in a cabinet. Luckily, installing your own dartboard cabinet is easy.

Part 1 of 3:

Finding the Right Location for Your Cabinet

Just in case a stray dart misses goes way off course, don't hang your dartboard cabinet near any valuable paintings or close to anything fragile.

Measure the wall to make sure the cabinet will fit when it's open. Don't just measure the width of your cabinet when it's closed, or else the doors might be obstructed when the cabinet is fully unfolded.

5 feet 8 inches (1.73 m) for a regulation board." width="460" height="345" />

Measure a height of 5 feet 8 inches (1.73 m) for a regulation board. Regulation height for the bullseye of a dartboard is 5’8”, or 68 inches (1.7 m). If you're playing on a league or you just want to go by the official rules, hang your cabinet so your bullseye will be at this exact spot.

Measure so that the bullseye is at eye level if you are just playing for fun. If you're not concerned with having a regulation board, you can adjust the cabinet to a height that will be comfortable for you. Centering the cabinet so the bullseye will be at about eye level.

Advertisement Part 2 of 3:

Finding a Stud and Leveling the Cabinet

Use a stud finder to locate the studs behind your walls. Slide the stud finder across the wall until it indicates that it has detected a stud. Once you've found the first stud, mark it with an X at the height you decided on for your bullseye.

Locate the next stud. You'll need to anchor your cabinet in 2 studs to make sure it's secure. You can either use the stud finder again or you can measure 16 inches (41 cm) from the first spot, since that is the standard width between studs. Mark this spot with a pencil as well. [1] X Research source

Use wall anchors to secure your dartboard if you can't find studs. If you don’t have a stud finder or if there are no studs where you want to hang your board, you will need to use wall anchors to attach your cabinet to the wall. These are plastic or metal pieces which you place into the wall so the screws have something to attach to. Depending on the style of anchor you choose, you may have to drill a hole first, or they may be self-drilling. [2] X Research source

Center the cabinet over your studs at the bullseye mark. Most cabinets are made so that the bullseye will be located at the center of the cabinet. If this is the case, the mark you made to indicate your dartboard's height will be the center of your cabinet. Center the cabinet, then use your pencil again to mark where the pre-drilled screw holes are located.

If you are using a laser level, attach it to the wall and hang the cabinet so the top is parallel to the laser line. [4] X Research source

Advertisement Part 3 of 3:

Mounting the Cabinet

your cabinet doesn" width="460" height="345" />

Drill holes if your cabinet doesn't have them. Most dartboard cabinets come with pre-drilled holes for easy installation. In your cabinet, if your cabinet doesn’t have pre-drilled holes for the wall screws, you will need to drill 4 holes, one near each corner. Make sure the distance between the holes doesn't exceed 16 inches (41 cm) or you might not be able to anchor the cabinet in your studs.

Use screws to mount the cabinet to the studs in the walls. Most dartboard cabinets come with all of the hardware you will need to mount it. Use a cordless drill to secure the cabinet using the provided screws.

your cabinet doesn’t have screws with it." width="460" height="345" />

Use a #8 screw if your cabinet doesn’t have screws with it. A #8 screw, also known as a 5 ⁄₃₂ inch (4.0 mm), is a standard screw for installation projects. Look for one in about a 2” (51mm) length. [5] X Research source

Adjust the cabinet as needed. After you hang your cabinet, check it again with the level and measure the height of the bullseye. If you need to make any adjustments, remove the screws, shift the cabinet until it's in the right location, then resecure the cabinet with the screws.

Expert Q&A

Ask a Question 200 characters left Include your email address to get a message when this question is answered. Advertisement

Tips

Submit a Tip All tip submissions are carefully reviewed before being published Please provide your name and last initial Thanks for submitting a tip for review! Things You’ll Need